Ridgeway grandfather clocks7/12/2023 ![]() The time weight is the center weight which can be light or heavy depending on bob size. This will hopefully be enough to activate and run the chime on its own. When you advance the time and make it chime, the weight will slowly come down. At the same time, turn the minute hand past the quarter hour to see if it will engage the chime. This is the same as making the weight weigh more. Using cloth gloves, or at least a cloth of some kind, pull down on the weight some. The chime weight is on the right as you face the clock and has the heaviest weight. Never go to the point where the top of the shiny weight cover can't be seen. When winding the weights up make sure the top of the weight can be seen when done. The grandmother and grandfather chain drive units often do not have this feature. Some larger clocks have over wind protection to prevent this. The Grandfather clock weights can get stuck in the high position if over wound. In addition, UPS charges a fee to send a call tag for them to come back. Then it is $30 to get them back to us and another $30 to send out a new set. For example, suppose we charge $30 to ship these and for some reason they are wrong. To return these is not an inexpensive or easy task. It is best to get the right weights the first time. With that said, we don't want to ship these back and forth. Sure one weight set of three is less than 30 lbs but that adds up quickly in a stack of weight sets. Grandfather clock Weights are not cheap mainly because they are so heavy to keep, ship, store, move from here to there. Grandfather Clock Weights Description - Conclusion A lighter weight may or may not be fine because it may not trigger the movement to work properly. If the weights are a little too heavy it is fine. In fact, there is a lot of clocks in the world sold new with the wrong Clock Weights on them from the start.Ĭlockworks will do a repair and they will say the clock ran for 30 years straight and come to find out they had Grandfather clock weights that were a pound or two too heavy. If it's a little under, that is fine also. Just know if it is a pound over that is fine. There has to be some sort of reference for the factory to label the Grandfather clock weights so it is what it is. In fact if ordering a 4.7 lb weight, it may come 5.3 or whatever, but that is just fine. If getting it close to those numbers that is fine. The weight specs list it as 4.7 or 6.6, however this is really being too picky. Also this rule is not for all Grandfather clock weights but the vast majority of the post WW2 German units. These specifications do not apply if the clock has 5 or 9 big tubes on the back. This changes to and in 60mm diameter if the pendulum bob is 8 1/2 inches or wider. A movement that is rectangle in either chain or cable will use and LBS in 60mm diameter. If the pendulum bob is 8 1/2 inches or more, change that rule to lbs and in 47mm or 43mm. These are available in either 47mm or 43mm diameters. If the movement is square and chain driven, it will require lbs and lbs. If the movement was made in Germany, post WW2, we can safely make the following assumptions. There is also another way to go about this task, which may be easier. ![]() Once the manufacturer is known and the starting numbers of the movement, use the chart to see the weight specifications for the Grandfather clock weights. Use the movement identification page to find out who made it. The stamp with these numbers are right on the back plate. The numbers on the movement is what will lead to getting the correct manufacturer of the movement not the names on the movement. This can be deceiving because the movement can have any name on it, but it may not be the true maker.įor example, a Hermle unit may have the name Sligh, Ridgeway, Howard Miller and so on. ![]() The weight chartīefore using the chart, you need to know who made the clock movement. The bob is the round disk at the bottom of the pendulum. The diameter of the bob in another piece of information that needs to be known. Once the movement number is known, cross reference that with the weight chart. This information will not be on any of the paperwork or clock case. This requires getting the information off of the back plate of the brass movement itself. If needing a complete clock weight, we need to determine what the appropriate weight is for the clock. Any part of the weight is available on its own. The Grandfather Clock Weights Description on this web page will cover what is meant by weights and their parts.
0 Comments
Leave a Reply. |